OSW1×18 TTL optical fiber switch
Introduction of OSW 1*18 optical fiber switch
Optical switch is a kind of functional component, with the ability of switching optical route. In optical fiber transmission system, it is used for multi-channel fiber monitoring, multi light source/ detector selection, and optical fiber path protection etc. Besides, it is also used in optical fiber test system for optical fiber and its component test, outdoor cable test and multi-spot optical sensors monitoring system.
Product Features of TTL optical switch
·Low Loss and High Reliability
·Parallel Interface (TTL)
·Modularized Design
·Epoxy-free on Optical Path
Specifications
| Parameters | Unit | OSW1×18 | |
| Insertion Loss | dB | ≤ 1.0 | |
| Wavelength Range | nm | 850±40 / 1300±40,MM | 1260 ~ 1650 SM |
| Test Wavelength | nm | 850 / 1300,MM | 1310 / 1550 SM |
| Return Loss | dB | MM ≥ 30 SM ≥ 50 | |
| PDL | dB | ≤ 0.05 | |
| WDL | dB | ≤ 0.25 | |
| TDL | dB | ≤ 0.25 | |
| Repeatability | dB | ≤ ±0.05 | |
| Durability | Cycles | ≥ 10 Million | |
| Switching Time | ms | ≤ 10(Sequence switch time of adjacent channel) | |
| Optical Power | mW | ≤500 | |
| Operating Temperature | ℃ | -5 ~ +70 | |
| Storage Temperature | ℃ | -40 ~ +85 | |
| Relative Humidity | % | 5 ~ 95 | |
Pin Configurations
DB-15 male connector
| Pin No. | Signal Name | I / O | Description |
| 2 | D0 | Input | TTL, Channel selection bit 0 |
| 3 | D1 | Input | TTL, Channel selection bit 1 |
| 4 | D2 | Input | TTL, Channel selection bit 2 |
| 5 | D3 | Input | TTL, Channel selection bit 3 |
| 6 | D4 | Input | TTL, Channel selection bit 4 |
| 11 | /RESET | Input | TTL, Low level reset to channel 0. High level means channel selection bits are effective. |
| 7 | /READY | Output | TTL, Ready (High=Not ready, Low=Ready) |
| 8 | ERROR | Output | TTL, Error (High=Error, Low=No error) |
| 1, 9 | GND | Input | Ground |
| 15 | +5VDC | Input | 5.0±5% VDC Digital power supply (max 50mA) |
| 12 | VM | Input | 5.0±5% VDC Drive power supply (max 800mA) |
| 14 | ISP | Input | TTL, For internal firmware upgrade of the module, in the normal mode, please suspended the pin; In the upgrade mode, please send the pin to ground. |
| 10, 13 | NA |
Channel Selection Table
| Max Channel | Input | Active Channel | |||||||
| /RESET | D6 | D5 | D4 | D3 | D2 | D1 | D0 | ||
| N=128 | 0 | x | x | x | x | x | x | x | 0 reset |
| 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | COM → 1 | |
| 0 | 0 | 0 | 0 | 0 | 0 | 1 | COM → 2 | ||
| 0 | 0 | 0 | 0 | 0 | 1 | 0 | COM → 3 | ||
| … | … | … | … | … | … | … | … | ||
| 1 | 1 | 1 | 1 | 1 | 1 | 1 | COM → 128 | ||
Dimension(DBx male head or female head is defined as the actual mark of the element)
Ø 01: 135×60×32-DB9 (N≤18, DB-15 male)
Ordering Information: 7202-1×18L-T-A-B-C-D-E-F-G
Example:7202-1×18L-T-SM-FS-5-90-12-02M-FA
| A | B | C | D | E | F | G |
| Fiber Type | Test Wavelength | Operating Voltage | Tube Type | Fiber Length | Dimension | Connector |
|
SM: SM, 9/125 M5: MM, 50/125 M6: MM, 62.5/125 X: Others |
85: 850±40nm O: O band(1260~1360nm) C: C band(1530~1565nm) L: L band(1565~1625nm) U: U band(1625~1675nm) FS: 1260~1650nm |
5:5V |
25: 250um 90: 900um 20: 2mm 30: 3mm X: Others |
05: 0.5m±5m 10: 1.0m±5m 12: 1.2m±5m 15: 1.5m±5m X: Others |
01: 135×40×32-DB9 02: 135×60×32-DB9 X: Others x=F:female M:male |
OO: None LP: LC/PC LU: LC/UPC LA: LC/APC FP: FC/PC FU: FC/UPC FA: FC/APC SP: SC/PC SU: SC/UPC SA: SC/APC STP: ST/PC STA: ST/APC X: Others |
FAQ:
Q1. Can I have a sample order for optical fiber switch?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.
